You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
Recent content by ktm265
-
K
Ain't Your Daddy's UTV
Thanks guys... Here is one last picture with all the body panels on. I would think with the market for UTVs going, Honda would want to get this badboy back in their line-up.- ktm265
- Post #61
- Forum: UTV Vehicle Builds - Show & Tell
-
K
Ain't Your Daddy's UTV
It's been pretty much a full year working on this project off and on...it's done now. I added a little bling to the motor...just to give it that polished look...- ktm265
- Post #59
- Forum: UTV Vehicle Builds - Show & Tell
-
K
Beware of Blingstar!
The Blingstar site has a link to contact them... I just sent a link to her story with the comment: "Really, very disappointing". Hard to argue the before and after... -
K
Need Flatbed
I know of one in Iowa...8x8 roughly with tie-downs...sitting on a 1 ton 95 Chev...buy it, drive out there...pull the flatbed and sell the truck.- ktm265
- Post #2
- Forum: Tow Rigs, Toy Haulers, and RV's
-
K
Ain't Your Daddy's UTV
Finally getting around to adding a new picture... Just waiting to drop the motor in.- ktm265
- Post #56
- Forum: UTV Vehicle Builds - Show & Tell
-
K
Ain't Your Daddy's UTV
The powder coating on the frame is completed, going to start bolting it back together. RPC out of Palo IA has the motor, giving it a new bore and piston...old pull down and check over to make sure the motor is 110%.- ktm265
- Post #54
- Forum: UTV Vehicle Builds - Show & Tell
-
K
Ain't Your Daddy's UTV
Dropped the motor off with RPC tonight out of Palo IA...Dan and Brian are going to go through it. Decided to stick with the stocker and not do the CR500...If the CR500 upgrade blows on me, there is no replacement or going back...Monday I'll should hear back on how the 400 bore was...- ktm265
- Post #53
- Forum: UTV Vehicle Builds - Show & Tell
-
K
Ain't Your Daddy's UTV
Been a while since I updated... It's in the shop being pulled down for powder coating... Took it to a harescramble, had some heating issues when the switch to turn the fan on and off went out...other than that, ran great. We raced with just the minimal body panels on so we could check on the...- ktm265
- Post #52
- Forum: UTV Vehicle Builds - Show & Tell
-
K
Ain't Your Daddy's UTV
Shake down report... Please let me start this off by 1st saying this... "IN YOUR FACE HOSER!!!" The front end modification that he was so critical about worked great... Still have some push but this was due to the rear end not having a differential...the suspension worked perfect, soaked up...- ktm265
- Post #51
- Forum: UTV Vehicle Builds - Show & Tell
-
K
Ain't Your Daddy's UTV
We have one side pretty much fabbed in for the body work, 2 more panels to go. We decided to leave them as individual pieces so they can easily be repaired or replaced if damaged.- ktm265
- Post #50
- Forum: UTV Vehicle Builds - Show & Tell
-
K
Ain't Your Daddy's UTV
Couple of pictures of it... Now we are putting on a few finishing touches, moving a few attachment points for various little things...Once it's all done, we'll strip it down to the frame and off to the powder coater...- ktm265
- Post #49
- Forum: UTV Vehicle Builds - Show & Tell
-
K
All UTV's Air Fox Shock adjustments...need expert advice
I read this about a Fox air shock modification on another site... The FOX air shox use nitrogen for the spring to change spring rates you adjust the amount of oil inside the reservoir body to do this you need to remove the nitrogen and valve stem or end cap, pour in more oil in the reservoir...- ktm265
- Thread
- Replies: 0
- Forum: UTV Chassis & Suspension
-
K
Hoser
After reading about Trever it reminded me of a recent exchange I had with guy named Hoser who must be related somehow to Trever... Lesson here is to just do your homework folks, it's out there and not hard to find. Hoser owns a website dedicated to the Honda Oddysses/Pilots... my FL400R build... -
K
Beware TREVOR SMITH @ 747INK.must read
Well I do find this funny, I'm not even in that area to race or witness this...Fact is he's getting his @$$ handed to him...sounds like his builds suck, his drivers can't win in cheater cars and his daughter gets the blame... If I was his daughter, I would go race for someone else. Like you... -
K
Ain't Your Daddy's UTV
Tomorrow AJ will get the shocks mounted up. Will take the measured length of travel of the shocks and find the optimum position so it's using the full length of travel and keep the ride height close to stock.- ktm265
- Post #48
- Forum: UTV Vehicle Builds - Show & Tell